Replacement Grease Filter for Ventline RV PR8-100 Range Hoods

Question

Question:

Looks just like the 8inch aluminum you show. Do you have a 7inch filter. Mine is clean but behind the stove! Seems I read widows do that. Ill have to get a son to help if not. Thanks

asked by: Judy

0

Expert Reply:

I checked our inventory and I could not find a 7" filter for PR8-100. However, I called Ventline and confirmed with one of my contacts that # BCC0246-00 fits your range. This item fits PR series vertical 5" diameter round outlet.

I have linked a picture of how the PR hood looks.

expert reply by: Timothy G

0

click to enlarge

Answer 1

We do have the replacement grease filter(s) that you are needing for your Ventline Pinnacle RV range hood. - Replacement Grease Filter Kit for Ventline Pinnacle Low Profile 12V Range Hood #VE24QR (this is a pack of 6)

view full answer...

Answer 2

I believe you are looking for the fan part #BCD0409-00 and the motor part #BVD0278-00. For the filter part #BCC0246-00 and for the switch part #BL0108-02. The fan does not use a nut to secure though.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Grease Filter for Ventline RV PR8-100 Range Hoods

Product Page this Question was Asked From

Continue Researching