Replacement Kodiak 13" Hub and Rotor with 8 on 6-1/2" Bolt Pattern

Question

Question:

Rotor/hub-133-7-8-DAC is the # Kodiak trailer gave me , what is the part I need to replace this ? Also a good high quality grease cap, something with thicker metal like in picture these are on a dexter 7000 lb triple axle car trailer

asked by: Fred

0

Expert Reply:

The part 133-7-8-DAC you referenced is a Kodiak 13" hub and rotor with a 8 on 6-1/2" bolt pattern, 1/2" lug studs, and a dacromet finish. I do have options that will work for you but we do not have this exact replacement. Instead, we have the raw part # KHR13712 and e-coat part # KHR13712E versions of this hub/rotor.

Please note that none of the above hub/rotors come with the bearings or seal. To replace them you will also want to use the following:

Inner Bearing - part # 25580

Outer Bearing - part # 14125A

Grease Seal - part # RG06-070

Unfortunately, we do not have a grease cap that will work with the above hub/rotors. You would need to find one designed to fit a 2.715" opening.

expert reply by: Conner L

0

Answer 1

Yes, the 7-Piece Installation Set for Bearings, Races, and Seals #PTW83020 that you referenced will work with the races you mentioned as they are very common races found on trailer axles which is what this kit is designed to fit.

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Kodiak 13" Hub and Rotor with 8 on 6-1/2" Bolt Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching