USA Made Gooseneck Hitch Recommendation for 2002 Ford Super Duty

Question

Question:

Where is this hitch made? Thank you

asked by: Wes

0

Expert Reply:

I did some checking and the rail/bracket kit of the Curt EZR gooseneck hitch part # C60685 is made in the USA but the center section with the gooseneck ball is made overseas.

For a hitch that is a confirmed fit for your 2002 Ford F-Series Super Duty that is made in the USA totally we have the B and W hitch part # BWGNRK1108.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

For a 12-1/4" x 2-1/2" Dexter electric brake assembly you will need the following parts: Left Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining for Dexter - item #BP04-236 Right Hand - 12-1/4" x 2-1/2" Brake Shoe and Lining…

view full answer...

Answer 4

To know if your 2017 Ford F-350 has an in-bed puck system installed you'll just need to look and see if you have four rounded attachment points (usually covered up when not in use, like in the attached picture). If you don't see these in your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 8

None of the options for the prep package are specifically designed to add height. Depending on the ball you have now you might be able to get a little more height out of the B&W Ball and Safety Chain Kit #BWGNXA2061. The installed height of this…

view full answer...

Answer 9

The two parts you mentioned (#RP87FR and #RP39FR) that fit your 2021 Ford F-350 Super Duty will both allow the ability to pull a gooseneck trailer with a gooseneck ball or use a 5th wheel hitch in the puck system. The only difference between them is…

view full answer...

Answer 10

Hey Luis, for your 2018 Ford F-350 that doesn't have the OEM pucks you would want the B and W Turnoverball hitch part #BWGNRK1116 that is a confirmed fit for your truck. I really like the B and W gooseneck hitches as they are known to be the…

view full answer...

Answer 11

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 12

Reese has a gooseneck ball that fits the OEM pucks of your 2020 GMC Sierra 3500 with the part #RP23FR but this doesn't have any rise built into it. The ball you mentioned does not fit your truck.

view full answer...

USA Made Gooseneck Hitch Recommendation for 2002 Ford Super Duty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching