Could TrailAir Flexair Pin Box Replace Mor/Ryde Pin Box

Question

Question:

I currently have a Moryde pin box. Will a Trail Air Flex be a direct replacement?

asked by: Mike D

1

Helpful Expert Reply:

As long as the Mor Ryde pin box you have was designed to replace a 1621 Lippert pin box the Trailair Flex Air pin box part # LC369535 would fit and work well.

Most likely your MorRyde would have a part number like Mor/Ryde SPB72-1621LD which if so you can see the "1621" in the number which means the Flexair mentioned is the correct one.

expert reply by: Jameson C

1

Answer 1

Yes, the MORryde Cushioned 5th Wheel Pin Box item #MR84VR, item #MR27VR, and item #MR44HR are all compatible with the Curt A20 5th Wheel Trailer Hitch w/ R20 Slider item #C16541. However, you will need to know the type of pin box your 2020 Grand…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Could TrailAir Flexair Pin Box Replace Mor/Ryde Pin Box

Product Page this Question was Asked From

Continue Researching