How To Install Replacement Kwikee Electric Step Motor and Linkage Kit To RV

Question

Question:

I have ordered parts LC379147 and LC379649. When I put the new pieces on the step should the step fully extended or fully retracted. Do I need to run motor to adjust linkage prior to pinning the linkage to the step?

asked by: Ron F

0

Expert Reply:

I contacted the manufacturer and to install the Lippert Components Kwikee Motor, Item # LC379147, and Kwikee Step Linkage Kit, Item # LC379649, you will need to fully extend the steps. After installing the motor, install the links and no adjusting will be required. The motor will make the adjustments after you complete the installation when it retracts.

Contact us if you have other questions.

expert reply by: Brint H

0

Harold S.

4/2/2020

I. Cannot get motor to break loose after removing the 3 screws 2 of them broke offWhat should I do to break it loose?Thanks

Reply

Chris R.

4/3/2020

Those 3 screws you removed should be all that's physically holding the motor to the step assembly. Sometimes the motor can kind of get stuck in place like you're experiencing, but other than using both hands to wiggle it free - gently (but firmly) rocking it back and forth as you pull down - there's not much else you can do. It should eventually break free.

Reply

Answer 1

Thanks for the order, and I have added a cut out of the instructions for how to install the Replacement Motor for Lippert Electric Coach Step #LC301695. These are the only instructions made available directly from the manufacturer.

view full answer...

Answer 2

The purple wire on Kwikee step modules does not need to be connected for it to function as this is an optional porch light switch circuit. Yours not being connected is most likely not the issue. See attached wiring diagram. In this diagram…

view full answer...

Answer 3

The correct replacement motor for your LCI motor 366043 on your Kwikee steps is Lippert Components Kwikee Motor and Screws for New IMGL Step Item #LC379147.

view full answer...

Answer 4

It sounds like you're trying to replace the motor on your Kwikee steps with the part number 366043, and we have just what you're looking for. In order to replace the motor for these steps you'll want to use the Replacement…

view full answer...

Answer 5

The Lippert #LC379147 is indeed the replacement motor for the 366043, and it is compatible with the #LC379160 'A' Linkage/gearbox.

view full answer...

Answer 6

We do have a wiring diagram for the Lippert Components Kwikee Step Rocker Switch #LC371010. I have attached a clip from the installation instructions that demonstrates how to wire this for you to check out.

view full answer...

Answer 7

For your Kwikee 32 Series RV steps, you can use the: -Replacement Motor for Kwikee Electric RV Steps #LC379147 for a replacement motor. For a replacement control module, you're going to need the: -Replacement Control Unit for Kwikee Electric RV…

view full answer...

Answer 8

It's possible the 25 amp inline fuse of the Kwikee step switch part #LC371010 is blown and that's why you are seeing it no work properly. If you check out the diagram I attached you can also check to make sure the switch has all of the wires…

view full answer...

Answer 9

Thanks for the pictures! Yes, the Replacement Motor for Kwikee Electric RV Steps - 12V item #LC379147 will replace your 2015 LCI 369545 motor.

view full answer...

Answer 10

Since your Georgie Boy Pursuit is a 2008 model, you will need the Lippert Components Kwikee Motor and Screws for New IMGL Step #LC379147. The motors changed from October to November of 2005, so you can rest assured it is the correct replacement.

view full answer...

Answer 11

Yes, you can absolutely use the Replacement Access Hatch for RVs #37231025 as an access hatch add-on to your fresh water tank; this product also comes with a waterproof seal that will prevent leakage.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How To Install Replacement Kwikee Electric Step Motor and Linkage Kit To RV

Product Page this Question was Asked From

Continue Researching