Does The Fulton Jack Mounting Bracket # P9012-00 Include Nut and Bolt Pictured

Question

Question:

does the nut and bolt come with the plate

asked by: Jon

0

Expert Reply:

Yes, the Fulton Jack Mounting Bracket, part # P9012-00, comes included with the nut and bolt.

If in the future you would need replacement hardware, we have the Replacement Hardware Kit For Fulton Swivel Jack, part # F0933325S00.

expert reply by: Reno H

0

Answer 1

The bolt holes of the Replacement Bolt-On Mounting Kit for Fulton XP Series Jacks #F500349 measure 3" apart on center in order to line up with the Jack Mounting Bracket #P9012-00.

view full answer...

Answer 2

Fulton marine jacks mount to a bracket that has holes that are 3 inches apart on center, the Jack Mounting Bracket for Fulton Marine Jack - Weld-On #P9012-00. There isn't going to be a way to mount a Fulton jack to a bracket with different…

view full answer...

Answer 3

There is indeed a replacement hardware/bushing kit available. You'd need part #F0933325S00. My Fulton representative confirms that this would be the correct replacement bushing for your Fulton Magnum 1500 lb capacity jack.

view full answer...

Answer 4

The Fulton Adapter Kit #F500320 will allow you to mount a Fulton F2 trailer jack to your current mounting bracket like part #P9012-00. The Wide Wheel #F1413040134 version of the F2 works on gravel. It will obviously be harder to move on gravel than…

view full answer...

Answer 5

It sure will! The Replacement Hardware Kit for Fulton Swivel Jack #F0933325S00 were looking at is confirmed to fit your older Fulton Magnum Swivel Jack made back in roughly 2006. This was confirmed by my contact at Fulton. I included a video of the…

view full answer...

Answer 6

The roll pins that are used in jacks like the Fulton model on your trailer can be difficult to remove because they fit very tightly into place. I just recommend using a punch that is a bit smaller in diameter than the pin and then tap it with a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Does The Fulton Jack Mounting Bracket # P9012-00 Include Nut and Bolt Pictured

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching