Shortest Garnish for the Ventline E-Z Lift Ventadome Trailer Roof Vent # V3092-601-00

Question

Question:

I need the thinnest trim piece for a fiberglass roof

asked by: Carl R

1

Helpful Expert Reply:

The shortest garnish pieces that will fit the Ventline E-Z Lift Ventadome Trailer Roof Vent # V3092-601-00 have a 1-1/8" leg. These come in Birch White # VA0445-25 and Polar White # VA0445-33.

i have attached a review video for you to reference.

expert reply by: Jon G

1

Answer 1

Not a saint, but I should still be able to help you out! I believe you are asking about a standard square roof vent on your trailer, and you really just need to know two things - the size of the cut out of the vent opening and the (approximate)…

view full answer...

Answer 2

For anything vertical that you're trying to seal or if you're under the trailer sealing and don't want the sealant to drip down you'll need Non-Sag Sealant for RVs #344270341437-1. For anything on top of the trailer…

view full answer...

Answer 3

For the Ventline E-Z Lift Ventadome Trailer Roof Vent #V3092-601-00, I recommend the MaxxAir Standard RV and Trailer Roof Vent Cover - 19" x 18-1/2" x 9-1/2" - White #MA00-933066. This cover will allow for full vent function and also…

view full answer...

Answer 4

We can definitely help with this. I suggest either the Ventline Ventadome Trailer Roof Vent, #V2110SP-24 that is a manual lift vent with a metal lid. Or, the Ventline E-Z Lift Ventadome Trailer Roof Vent, #V3092-601-00 which is also a manual lift but…

view full answer...

Answer 5

The insulators for standard 14x14 roof vents like part #CAM45192 do not fit into the vent opening of the MaxxAir Mini Roof Vent part #MA00-03700. The actual vent opening of the MaxxAir is 10-1/2" so the 14 inch insulator is not going to fit into…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...