Scissor Jack Replacement Recommendation for 2012 Rockwood 1940LTD

Question

Question:

Hello, I bent a stabilizer scissors jack on a new to me 2012 Rockwood 1940ltd. The worm gear is bent to the extent that is almost usable. Id like to bolt up to the existing holes, and purchase a single jack if possible. I can provide a tracing of the jack to frame mounting surface if helpful. The threaded frame hole match the smaller round holes on the jack that lie in the same plane as the worm gear. Does this make sense? New PUP owner who is blushing

asked by: Chuck

0

Expert Reply:

Thanks for the picture of the mounting bracket of your current scissor jacks. From that I can tell that the Ultra Fab Scissor jack part # UF48-979006 is a single scissor jack that would fit and work well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The mounting brackets for the scissor jacks we offer do vary. I went to the warehouse and took some measurements of the Lippert Components 24 inch Scissor Jack, part #LC285325. I have attached a photo of the mounting brackets with the dimensions…

view full answer...

Answer 2

The #TJSC-24 scissor style stabilizing jack isn't an RV specific product, if it's 2500 lb capacity and 18-3/4 inch lift and the pictured mounting bolt pattern is compatible with your Rockwood Mini-Lite, it'll work perfectly…

view full answer...

Answer 3

As long as you are able to get the motor to fit the Lippert Scissor Stabilizer Jack #LC285325 I see no problems with doing that. Typically you'd use the Manual Hand Crank #LC285324 to operate the jack which has a 3/4" socket. It…

view full answer...

Answer 4

The Lippert Scissor Stabilizer Jacks #LC285325 mounting plate is designed to be a universal fit that will match most scissor jacks installed at the factory, but it's not necessarily always going to be a perfect match. Unfortunately there is…

view full answer...

Answer 5

I have a solution for you, but when I called Lippert to confirm the size of the bolt on the Lippert Components Scissor Jack #LC285325 they informed me that this particular jack should not be raised or lowered using a power tool, but it does have a…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Scissor Jack Replacement Recommendation for 2012 Rockwood 1940LTD

Product Page this Question was Asked From

Continue Researching