Red Replacement Trailer Lens Recommendation for Enclosed Cargo Trailer Marked DZ-102 SAE-PL-69

Question

Question:

I have red DO-RAY DZ-102 SAE-PL-69 on my enclosed car trailer. They look to 4x2 in size. Is A66RB a good replacement? Thanks

asked by: Tim

1

Helpful Expert Reply:

Yes, based on the picture you included (that is somehow now gone) the correct replacement lens you need is the part # A66RB that you referenced.

expert reply by: Jameson C

1

Answer 1

The Replacement Red Lens #A42RB should be the correct replacement lens for your Do Ray SS-105. Since this is a common style of light duplicated by several manufacturers. To verify this you can check the measurements of the light you have, if they are…

view full answer...

Answer 2

The Replacement Amber Lens for MC66AB #A66AB or the Replacement Lens for MC31AB #A31AB are both 4 inches by 2-1/6 inch.

view full answer...

Answer 3

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 4

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Red Replacement Trailer Lens Recommendation for Enclosed Cargo Trailer Marked DZ-102 SAE-PL-69

Product Page this Question was Asked From

Continue Researching