Replacement Parts For Wobble Roller For Boat Trailer With 7/8 Inch Shaft

Question

Question:

I need to replace some of the rollers I Measured the shaft its 7/8 inch is this the correct replacement? What retainer clip and washer do I need?

asked by: Todd B

0

Expert Reply:

Yes, the Yates Ribbed Wobble Roller, Item # YR530R-7P, is what you need. I have clips and pal nuts in other sizes but nothing that fits a 7/8 inch shaft.

I have also attached a video for you to check out.

expert reply by: Brint H

0

Answer 1

The outer diameter of the CE Smith Wobble Roller Washer, #CE10983, is 2 inches. We had the washer in stock, so I took a few additional measurements that you can see in the attached image.

view full answer...

Answer 2

The CE Smith #CE27610 roller Guide-Ons aren't trailer specific, so they'll work for most trailers. The U-bolt kit included with the guide-ons will be compatible with trailer frame members from 3 inches wide x 4-1/4 inches tall. An extra-long…

view full answer...

Answer 3

Most of the boat trailer rollers that we carry, including #YR530R-8P, are not trailer specific. You would go by the measurements of the roller. This wobble roller has a 5 inch diameter and is 3 inches wide. It takes a 1 inch diameter shaft. Bushing…

view full answer...

Answer 4

Since you have a 7/8" diameter bearing opening it sounds like you need wobble rollers for a 7/8" diameter shaft. For a replacement we have the Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 5" Diameter - 7/8" Shaft #YR530R-7P.…

view full answer...

Answer 5

The Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 4-3/8" Diameter - 3/4" Shaft Item #YR343R-6P is for a 3/4" shaft. The correct replacement wheels you need is the Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 5" Diameter -…

view full answer...

Answer 6

The Yates Ribbed Wobble Roller, #YR500YW-8PEZ, is exactly what you need for your 1999 EZ Loader boat trailer. The bushings are included with this roller. For a hog ring, we offer part #CE10981 and you can use part #SW1000 for a washer. At this time,…

view full answer...

Answer 7

The #YR530R-7P does look similar to the wobble roller in your picture on your 1999 Magic Tilt boat trailer. The only way to be sure is to measure your current roller and shaft. This roller has a 5" diameter and width of 3". It fits a…

view full answer...

Answer 8

We have wobble rollers specifically designed for 3/4 inch shafts like yours. For that we have the part #YR343R-6P which has a center hole diameter just slightly under 7/8 inch to fit the 3/4 inch shaft the way it needs to. If you need a washer to go…

view full answer...

Answer 9

There are only a few rollers that we carry that list specific trailers that they will fit. For everything else, you will need to go by the dimensions of the roller to determine if it/they will fit your trailer. I have included a link to the wobble…

view full answer...

Answer 10

Boat trailer wobble rollers like #YR500YW-7P and not trailer-specific or brand-specific so if their dimensions match up you'll be fine using them as replacements. The key things to note are the size of the shaft hole in the roller, which is about…

view full answer...

Answer 11

Since you have a 7/8 inch wobble roller shaft you would want the part #YR500YW-7P as it is designed to fit a 7/8 inch shaft and is the same diameter as the roller you referenced, 5 inches. I attached a review video for you to check out as well.

view full answer...

Answer 12

I went out to the warehouse and pulled Yates boat roller #YR500YW-6P. The inside width where the shaft goes is 1-1/2 inches. I have included a link to a video review of this roller for you. Some related items you may also need are the retainer ring,…

view full answer...

Replacement Parts For Wobble Roller For Boat Trailer With 7/8 Inch Shaft

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching