Can Roadmaster EZ Base Plate Kit be Converted to EZ5 Base Plate

Question

Question:

can a roadmaster 521433 be adapted to replace a 521423

asked by: Rus

0

Expert Reply:

You would not be able to swap removable arms from a # 521433-1 to a # RM-521423-5. Both the portion that attaches to the frame and the removable arm section are made specific to each other so you'd have to replace the entire kit.

expert reply by: Jameson C

0

Answer 1

It's definitely possible to upgrade a trailer's axle rating to a higher rating by just swapping the axles. To pick out the correct axle you'll need to measure the distance between the hub faces and the spring seat centers and you'll…

view full answer...

Answer 2

If you are wanting to go to higher capacity leaf springs I would advise against it. The problem is that since the trailer axle is rated for 3,500 pounds you won't gain any additional capacity by switching to higher capacity springs. What it will…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Can Roadmaster EZ Base Plate Kit be Converted to EZ5 Base Plate

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching