Recommended Rear Anti-Sway Bar for 2008 Workhorse W24 Chassis

Question

Question:

I have 2008 Workhorse W24 Chassie. What is difference between RM1259-108 and RM1259-109 ? I want to buy the best I can. Thanks

asked by: Mike B

1

Helpful Expert Reply:

Both the Roadmaster Rear Anti-Sway Bar parts # RM-1259-109 and # RM-1259-108 that you referenced are designed to fit your 2008 Workhorse W24 Chassis. The difference between the two items is the RV length they are best suited for. If your RV is 33 feet or longer, you will want to go with # RM-1259-109 and if it is shorter than this you will need # RM-1259-108.

Either item will do a great job of minimizing sway and driver fatigue by improving the stability and driveability of the vehicle. It will mount to the rear axle and frame to balance weight transfer and reduce body roll.

I have attached the complete installation instructions for these products that you can also take a look at.

expert reply by: Chris R

1

Answer 1

Regardless of the length of your RV you can use the Roadmaster anti-sway bar #RM-1259-108 (for 2003 Workhorse W20, W22, and W24 chassis). Bar #RM-1259-109 only fits the W22 and W24 chassis that are 33 feet long or longer like you said. Your 2003…

view full answer...

Answer 2

We have just what you need to improve the handling of your 2006 Fleetwood Bounder W22 chassis with the rear sway bar part #RM-1259-109. For Class A motorhomes like yours the biggest ride quality improvement you can make is with a rear sway bar. This…

view full answer...

Answer 3

We'll typically recommend folks start with a rear anti-sway bar which will solve handling problems the majority of the time. For your 36 foot 2002 Workhorse chassis, use the #RM-1259-109. If your motorhome follows ruts in the pavement, you'd…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 8

I see what you mean about the cover being "recessed" into the front of the trailer. After looking thru a few pictures of these 2005 Trail Lite Hybrid trailers, it appears to be a fairly unique tank cover. I am sorry to say that we do not…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Ron, thanks for reaching out! We have two different steering stabilizers for your motorhome on a 2018 Ford F-53 chassis; the Roadmaster Reflex and the Roadmaster Exact Center. The Exact Center was supposed to be an upgrade to the Reflex but after…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Recommended Rear Anti-Sway Bar for 2008 Workhorse W24 Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching