Recommended Trailer Landing Gear with Independent Motors for 2009 Heartland Cyclone 3950

Question

Question:

can you tell me what i need to convert my electric jacks to a two motor independent system. i have a 2009 Heartland Cyclone 3950 model. i believe it has a Venture jack system.

asked by: Scott S

0

Expert Reply:

The easiest way to make your 2009 Heartland Cyclone trailer an independent adjusting system is to use the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. This will come with two legs with the individual motors to allow easy leveling.

If you want to keep your current system, you can leave the lead leg as is and then replace the follow leg with a lead leg # LG-177202, add a gearbox # LG-179015, and a motor with switch # LG-217884.

expert reply by: Jason S

0

Answer 1

To determine if the Stromberg Carlson Manual Landing Gear Set #LG-183708 that you referenced will bolt up to the existing brackets you have on your trailer Coachmen Catalina, you will want to take a couple quick measurements on your current…

view full answer...

Answer 2

There unfortunately isn't a guide to tell us the weld stop spacing in your 2012 Genesis Supreme Vortex so you'll first want to measure so we can see if there's a compatible replacement without have to cut off your current…

view full answer...

Answer 3

For your VMC900R landing gear if you want to replace the lead leg I recommend the Replacement Lead Leg for Stromberg Carlson Landing Gear - 33-1/2" #LG-177202 and then for the follow leg #LG-177201. I've attached a photo of the…

view full answer...

Answer 4

I spoke with my contact at Stromberg Carlson who confirmed that the Replacement Lead Leg #LG-177202 will work well as a replacement for your Venture VMC900. Then for the matching follower leg you would want the part #LG-177201.

view full answer...

Answer 5

The Lippert part number you referenced is for the Ground Control 2.0 system which you'd have to use the part #LC241845 as a replacement for. There isn't a Stromberg part number that will work.

view full answer...

Answer 6

You should need repair kit #LG-146059 for the lead leg and #LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

view full answer...

Answer 7

In order to determine which replacement lead leg you need, you'll need to know the model of the landing gear on your trailer (we have no way of knowing what you have), and measure it's outer tube length. For example, if you have a…

view full answer...

Answer 8

If you are in need of a replacement lead leg for your Venture vmc900r you'd want the part #LG-177202 or for a follow leg part #LG-177201. The lead leg is the one you'd attach the crank handle to and the follow leg is the leg that is…

view full answer...

Answer 9

I have attached a photo for you that shows how to properly measure the outer tube on a landing gear leg. I have not heard of a landing gear leg with a 36-1/2" long outer tube so if this is what you have then I recommend you replace both the lead…

view full answer...

Answer 10

Your Raptor Toy Hauler likely has a landing gear setup similar to the one you were looking at: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs #LC333964. If so, then the correct replacement motor would be Lippert Components…

view full answer...

Answer 11

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...