Complete Towing Setup for a 2018 Toyota Corolla iM
Question:
I have a 2018 Corolla. I'd like to put a hitch on it to pull my little jon boat 200lbs with a trailer that weighs maybe 300 lbs, to a lake 5 miles away from my house in North Carolina some hills! good roads. What do you recommend?
asked by: Rich
Expert Reply:
I have exactly what you will need to tow your small john boat to the lake with your 2018 Toyota Corolla. For starters you will need a trailer hitch and for that I recommend the Draw-Tite Sportframe Trailer Hitch Receiver part # 24952. The Draw-Tite Sportframe is a Class I hitch with a 1-1/4" receiver tube opening. I have attached an installation video of this hitch installed on a similar 2017 Toyota Corolla for you which as you can see is very simple and straightforward.
Then if your trailer has lights as most due you will need a wiring harness and for that I recommend the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11141824 which is a direct fit for your vehicle and will not require you to cut or splice any wires. It features a simple plug and play installation.
You will also need a ball mount/hitch ball and for your iM, the Draw-Tite Drawbar part # 3593 should do just fine for you. However, you will want to glance over the attached ball mount help article to be sure the above ball mount provides you with the correct amount of rise/drop. Odds are that your trailer has a 1-7/8" coupler therefore you will also need the Hitch Ball part # 19256 to complete your towing setup.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Hopkins
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Carry Bikes While Flat Towing a 2018 Toyota Corolla iM
- Q&A: How to Replace Kuat NV 2.0 Lock Core Without Key?
- Q&A: Dingy Towing for 2017/2018 Toyota Corolla iM
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Q&A: Replacing Leaf Springs On Trailer To A Lower Capacity To Avoid Road Shock
- Q&A: What Size Socket Works with 1 Inch Spindle Castle Nut # 165686?
- Q&A: Are there Bolt-On Hangers for Trailer Leaf Spring Suspension
- Q&A: Where is the Brake Controller Plug on my 2019 Chevrolet Silverado 1500 LD
- Article: Trailer Tire Sizing