How Does Lens Come off of Light Buster Backup and Utility Light # C8020

Question

Question:

How do toy replace the light? I cannot get the clear Plastic cover off

asked by: Bill A

1

Helpful Expert Reply:

You'll need a small slot screwdriver to slide into the slot you see the arrow in the picture I attached pointing out to gently pry off the lens.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

Some newer cars, vans and small trucks, especially those with large, aftermarket tires, may require the use of Class S chains. Class S tire chains are designed for use on vehicles with restricted wheel well clearance. I have attached a photo that…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 9

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 10

Hey Gary, so the Yakima 54" Tracks for Roof Racks #Y26RR that you referenced are compatible with your setup as they provide the standard dimension roof tracks that your Sherpa Crows Nest was designed to fit. With that said the correct T-bolt…

view full answer...

Answer 11

I have a great solution for you! I really like the Firestone Ride-Rite Air Helper Springs that you looked at they are by far the best bags for the money. The major reason is the way the air bags are connected to the caps on the end Firestone uses a…

view full answer...

Answer 12

If you have a 2017 Toyota Tacoma with the tow package/factory 7-way yes it is pre-wired for a brake controller. For a brake controller I recommend the Prodigy P3 Brake Controller part #90195. This is our best selling brake controller because of how…

view full answer...

How Does Lens Come off of Light Buster Backup and Utility Light # C8020

Product Page this Question was Asked From

Continue Researching