Dimensions on Firestone Replacement Upper Bracket # F5376

Question

Question:

What is the hole spacing and overall width of the Firestone F5376 upper mounting bracket? 2001 F-250 SD Crew 4X4 with RBW Lil Rocker 5th wheel hitch.

asked by: William M

0

Expert Reply:

I went out to our warehouse to take a look at the Replacement Upper Bracket for Firestone Ride-Rite Rear Helper Springs # F5376 referenced in your question. The mounting holes on the side brackets are spaced apart 1-1/2 inches, center to center. The bracket itself has an overall length, with the side brackets included, of 13-1/2 inches and a width of 5-1/4 inches. Inside the mounting brackets the length is 10-3/4 inches.

I have attached an image with these dimensions labeled that you can also take a look at.

Please note that this particular replacement bracket is designed for the Firestone Ride-Rite Air Helper Springs # F2071. This air spring kit is confirmed to fit your 2001 Ford F-250, however it is not compatible with an in-bed hitch. For a Ride-Rite Air Helper Spring Kit that will work with an in-bed hitch, I instead recommend the Firestone # F2550.

I have included an installation video on this product that you can also use for reference.

expert reply by: Chris R

0

click to enlarge

Answer 1

We have the bracket you are looking for, I spoke with my contact at Firestone and the correct bracket you are looking for your Firestone kit part #F2407 is the part #F5494. I attached a picture that has all of the fasteners sizes that come with the…

view full answer...

Answer 2

The replacement brackets you'd need for the #F2071 are the part #F5376 (quantity 2) for the upper brackets, part #F5092 (quantity 2) for the lower brackets, #F5086 (quantity 4) for the bracket straps, and part #F5093 (quantity 4) for the other…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Dimensions on Firestone Replacement Upper Bracket # F5376

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching