Height Adjustability of Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer # UF19-950500

Question

Question:

what is the height adjustment??

asked by: William

0

Expert Reply:

The height adjustability of the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer # UF19-950500 that you referenced is 31" - 54".

expert reply by: Jameson C

0

Lee B.

10/28/2021

with a king pin ht of 50 inches, how high of a tripod stabilizer should you use?

Reply

Les D.

10/29/2021

The Ultra-Fab # UF19-950600 Kin Pin stabilizer is the perfect solution for your 50 inch high king pin. This tripod stabilizer is adjustable from 33 to 62 inches.

Reply

Answer 1

The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part #UF19-950200 would be best for harsher environments. The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part #UF19-950600 has a black coating which will also resists rust but if this coating…

view full answer...

Answer 2

The SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet #SP54FR6 will fit your 2022 Grand Design Momentum 399TH as long as you have 9" round jack feet. This is most likely what you have. But the foot size/shape of the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hey Tim, so the Ultra Fab Landing Gear part #UF17-943010 does use a more unusual weld stop dimension as it's 20-1/4 inches from outside to outside of the it's weld stops. So since it looks like you already ordered this you can still make it…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Jon, Yes, the Advent Air Low Profile RV Air Conditioner #ADV79FR is compatible with the Air Distribution Box #ACDB. This would have the controls on the air distribution box instead of a wall mounted thermostat. We don't currently have any…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 11

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...

Height Adjustability of Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer # UF19-950500

Product Page this Question was Asked From

Continue Researching