Picking Out Replacement Landing Gear Box for 2007 Fleetwood GearBox 335fs

Question

Question:

I have a 2007 Fleetwood GearBox 335fs. Need to replace the Fifth Wheel Landing Gear Box, is this the Gearbox I need ? I dont know if this is the correct Part number? LC276602 Thank You,

asked by: Francisco C

0

Expert Reply:

The part # LC276602 is a gear box that fits the vast majority of landing gear sets found on RVs. If what you have looks like this and is plastic or aluminum like this it will fit and work well.

If you have something different email me back a brand or a picture and I'll take a look.

expert reply by: Jameson C

0

Answer 1

The landing gear looks like a standard set based on the pictures and the dimensions you listed. The part #LC146060 would be what you need for the follow leg and then part #LC146059 for the lead leg.

view full answer...

Answer 2

It looks like the 2004 Dutchmen Sport 26 footer has a gross weight of 6,720 pounds but I can't say if that is the gross weight or the dry weight. Tongue weight is usually 10 to 15 percent of the gross trailer weight. So for a trailer that weighs…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Picking Out Replacement Landing Gear Box for 2007 Fleetwood GearBox 335fs

Product Page this Question was Asked From

Continue Researching