2017 Honda CR-V Touring Trailer Hitch

Question

Question:

Hi, Im interested in a trailer hitch for a 2017 Honda CR-V. I see you carry a trailer hitch, but the I have the Touring model that has a couple of sensors in the rear for tail-gate opening etc... Can you tell me if the trailer hitches interfere with these sensing functions? Thank you.

asked by: Michael B

0

Expert Reply:

We had a customer come back and state that the Draw Tite Hitch part # 36597 fit and worked well on their 2017 Honda CR-V Touring so we know it would be a great choice. You will most likely just have to kick to either side of the hitch opening to get the lift gate to open.

Everything needed to install the hitch is included as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Draw-Tite is one of the leading trailer hitch manufacturers and they make hitches for almost every vehicle on the market. For a 2018 Honda CR-V you would use something like part #DT79MR but this is only designed to fit 2017-Current CR-Vs. If you have…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 10

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

2017 Honda CR-V Touring Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching