Least Visible Trailer Hitch Recommendation for 2015 Ford Mustang Fastback
Question:
Which hitch for the 2015 Mustang Fastback is the least visible, I plan to pull a small tear trailer that will weight 700 lbs but do not want to see the receiver when not towing.
asked by: Keith
Helpful Expert Reply:
The Draw Tite hitch part # 24928 would be less visible than the Curt # C11405 because it sits 1/2 an inch higher and it doesn't have a collar around the opening of the hitch. Instead it's just an open shank which would be slightly less visible.
For trailer wiring you'd then want the part # 118487 which is a confirmed fit.
For a ball mount you'd then want the part # 3594, 2 inch hitch ball # 19258 or 1-7/8 inch ball # 19256.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Charge a Dump Trailer Battery
- Q&A: Trailer Grease Seal to Replace 127194TB
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Q&A: Replacement Leaf Spring Bolts and Bushings for Dexter 10K Axle On Big Tex Trailer
- Q&A: Does Correct Track Trailer Alignment Kit # RR23QX Come with Enough Brackets for Tandem Trailer
- Q&A: Replacing Parallex 7345 Converter to One that is Compatible with Lithium Batteries
- Q&A: Will the Correct Track Trailer Alignment and Lift Kit Prevent Nose High Towing
- Q&A: Recommended Replacement For A WFCO WF-8750P Power Center
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Trailer Hitch Receiver Sizes
- Article: Trailer Maintenance Schedule
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: What is Boondocking