Recommended Trailer Hitch Receiver For 2017 Toyota Tacoma
Question:
Regarding the rear tow hitch for a 2017 Tacoma. Do you guys provide the pull wire for the screws. And if not where would I go about getting them.
asked by: Don P
Expert Reply:
For your 2017 Toyota Tacoma, I recommend the Curt Trailer Hitch item # C13264. This hitch will come with the pull wire needed and all the hardware. This is a very strong hitch receiver with an e-coat base and powder coat finish. This is a confirmed fit for your truck and I've attached the installation details for you.
For your wiring, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56349. This custom-fit T-Connector plugs into your Toyota Tacoma's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
I recommend using the Mounting Bracket 4-Pole Flat # 18144 to hold your trailer connection in place with the No-Drill Mount Bracket # 18140.
For a ball mount, I recommend the B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black # BWTS10037B. This will give you an adjustable mount to tow multiple trailers level. It also has two integrated hitch balls to fit a 2 inch coupler or a 2-5/16 inch coupler. This ball mount has a really nice and clean looking stow away option that will protect your shins when not in use. I recommend using a hitch lock like # e98882 to protect your investment.
Products Referenced in This Question
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 10K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 5 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- B and W
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Q&A: Solution for Atwood Surge Brake Coupler Needing Replacement Parts
- Article: Pintle-Hitches
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Does The etrailer Invisible Base Plate Kit # e86YR Need An Adapter For A Blue Ox Aventa II Tow Bar
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Key Needed for Gorilla Guard Trailer Coupler Lock
- Q&A: Replacement Conversion Kit For Motor For # 781005
- Article: Trailer Wiring Diagrams
- Article: Big Truck Big RV
- Q&A: Trailer Hitch Fit for 2022 Kia Niro PHEV Plug In Hybrid
- Q&A: How To Mount 7-way Connector To Trailer Hitch Receiver On 2021 Subaru Ascent
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)