Recommended Weight Distribution System Carrier

Question

Question:

will your hitch grip fit a 2 inch ball?

asked by: Danny L

0

Expert Reply:

The HitchGrip Carrying Tool for Weight Distribution Head Assembly with 2-5/16" Ball # 303-HG-712 will not work with a 2 inch ball. You may be interested in the Classic Accessories Tow Bar and Weight Distribution Tote - 36" x 11" Wide x 8" Tall # CA80113 which will also allow you to carry and stow your system.

expert reply by: Jason S

0

Answer 1

The Axle Riser Kit - Single Square Torsion Axle part #LC382741 will lift both sides of the trailer frame up 3-1/2" to add clearance between the frame and the axle. To install the axle riser kit you want to raise the trailer one side at a time by…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Based on the information I could find the Samsung MR1031UWC is a countertop style microwave that is 20-11/32" wide, 13-11/32" tall and 14-5/8" deep. Currently we only have over the range and built in style microwaves. If your microwave…

view full answer...

Answer 8

Hey Roger, yes you could remove the trim of the High Pointe Built In Microwave part #HP84ZR and it could sit on a counter top like you asked about. The dimensions listed for it are correct for without the trim kit: 19" W x 11.375" H x…

view full answer...

Answer 9

I believe you're talking about the Furrion Propane RV Built-in Wall Oven #FSRD22LASS. This is 20-11/16" tall but the width is more than you can fit at 24-3/4" wide. These are the same dimensions as the Furrion Electric RV Built-in Wall…

view full answer...

Answer 10

If you check out the attached picture you can see where you'll find the serial number and date code on your cover.

view full answer...

Answer 11

The best way to power the interior lights in your trailer is with its own independent battery. You will not want to use the breakaway battery. The breakaway battery is only designed to operate the breakaway and will drain extremely quickly,…

view full answer...

Answer 12

Hello Gaby. I reached out to the manufacturer and found out that the UltraFab Weld-On Jumbo Steel Roller #UF48-979023 uses a 6-1.0mm Zerk fitting. For a replacement you can use the following: - Replacement Brass Grease Zerk for Weld-On Hinges - 6 mm…

view full answer...