Replacement Seals and Bearings for 4,400 lb Axle

Question

Question:

Inside Bearing: Dexter Kit - K71-390-00 / Industry - L68111/L68149 Outside Bearing: Dexter Kit - K71-307-00 / Industry - LM67010 / LM67048 Seal: On the seal brass it has Dexter 010-019-00 On rubber seal lip it has TCM 171255TB For the brake size of 10inch x 2-1/4inch it lists Seal Part No. for E-Z Lube as K71-305-00 Can you match this up and give me a price for bearings and 2 seals?

asked by: Ronald M

0

Expert Reply:

We have the bearings and seals you would need for your 4,400 lb axle. It would be inner bearing # L68149 with race # L68111, outer bearing # LM67048 with race # LM67010 and grease seal # RG06-050. You can find the prices of these parts on their product pages.

I've added links of video reviews of these products for you to take a look at as well.

expert reply by: Kyle S

0

Answer 1

We do carry the Lippert Electric Trailer Brake Assemblies Left #LC96WD and Right #LC46WD from Lippert for their 4,400lb axles. These brakes are self-adjusting like the Electric Trailer Brake Kit #AKEBRK-35-SA.

view full answer...

Answer 2

We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following: Bearings #L68149 and…

view full answer...

Answer 3

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 4

We've checked with MORryde in the past and with the Road Armor equalizer setups they've told us that the #MR33WR will work.

view full answer...

Answer 5

The seal for your Dexter 4,400 lb axle is part #58846 which we also have in a pack of 2 listed as part #RG06-050 these have an inner diameter of 1.719" and an outer diameter of 2.565".

view full answer...

Answer 6

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 or just the Grease Seal part #RG06-050.

view full answer...

Answer 7

You can use the #AKEBRK-7-SA to replace your existing Axletek brakes and they'll work well for you. This is a self adjusting set of brakes and will fit on your existing hubs; you'll also need brake mounting hardware, which is available with…

view full answer...

Answer 8

It sounds like the remains of a double lip seal. Was it like a rubber o-ring with a metal spring around it? You are going to have to replace the seal so I would just disregard the sleeve. It would go on the outside of the rubber lip though. I…

view full answer...

Answer 9

I did some research and it looks like the spring you need is 26 inches long and for a 4,400 lb trailer axle like you mentioned. We have a really easy solution for that with the part #e27SR which is 26 inches long and for a 4,500 lb trailer axle so it…

view full answer...

Answer 10

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 11

The piece you're referring to in the #LC26VR kit is called a "shoe". This part is plastic with foam pads on each end that helps cushion the motor bracket as it slides back and forth to either end of the track.

view full answer...

Answer 12

Actually, there's a little more to it than that. The magnets on the #K23-478-479 are a little different, but the primary difference is the mounting bolt pattern. On a typical 3500 lb brake assembly, the mounting studs will all be 2-7/8 inches…

view full answer...

Replacement Seals and Bearings for 4,400 lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching