Front Hitch Recommendation for 2011 Chevy Silverado 2500HD that Allows Tow Hooks to be Retained

Question

Question:

Which Front Hitch? 2011 - Chevy Silverdor - ext cab 2500 HD - -has front pull rings

asked by: John S

0

Expert Reply:

The Curt front hitch part # C31023 that you referenced does allow you to retain the front tow hooks of your 2011 Chevy Silverado 2500HD so it would be the better choice.

expert reply by: Jameson C

0

Answer 1

You bet we do! The Draw-Tite #65078 and the Curt #C31023 front mount receivers are a fit for your 2015 Sierra 2500. The Draw-Tite model isn't a fit for Denali models, and might require you trim the fascia in order for the receiver tube to pass…

view full answer...

Answer 2

I have a great solution for you. Unfortunately the Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches #HLY94FR will not work with your 4-inch tires. However, for a platform rack that also attaches at the bikes'…

view full answer...

Answer 3

The Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches Item #HLY74FR referenced in your question is compatible with your 2-inch receiver and fat bike tires up to 5 inches in width. It is also approved for…

view full answer...

Answer 4

I have another option for you, but the Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount #HLY94FR you were looking at is only rated to carry bikes weighing up to 35lbs each and will not be able to…

view full answer...

Answer 5

A 13,500 btu air conditioner normally draws right at 1,300 watts which the solar panel kit part #34282184 can only provide up to 380 watts at peak performance. The highest wattage setup we have from solar panels is the #34282185 which is capable of…

view full answer...

Answer 6

I recommend the Curt Front Mount Trailer Hitch Receiver #C31023 for your 2013 Chevrolet Silverado. It will come out lower on the truck to clear the Ranch Hand front bumper you have. The Draw-Tite Front Mount Trailer Hitch Receiver #65078 comes out of…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...