Screws for Replacement Rubber Blocks for TracRac Systems

Question

Question:

does this include the nut/plate for bolt to go into?

asked by: Paul G

0

Expert Reply:

The Replacement Rubber Blocks, part # TARB-11032-1 do not include the nuts and bolts to attach to the rail.

There are hardware kits available that will fully replace the nuts, bolts and washers for the Trac Rack:

If you have a short-bed truck, you'll want Hardware Kit, part # TAHD-21501

If you have a long-bed truck, you'll want Hardware Kit, part # TAHD-21000-A

expert reply by: Jacob W

0

Answer 1

Thule offers the strips you speak of in a replacement hardware kit, part #752-186-3001. They do not offer the strips as a separate item.

view full answer...

Answer 2

If you have a short bed 2016 RAM 2500, you will need the Replacement Hardware Kit for TracRac Sliding Ladder Rack Base Rails - Short Bed Trucks #TAHD-21501. If you have a long bed 2016 RAM 2500, you will need the Replacement Hardware Kit for…

view full answer...

Answer 3

There is replacement hardware available for TracRac models TA21500 and TA21501 base rails. We carry the Replacement Hardware Kit for TracRac Sliding Ladder Rack Base Rails - Short Bed Trucks #TAHD-21501 which includes 4 steel pocket nuts, (8)…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Screws for Replacement Rubber Blocks for TracRac Systems

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching