Replacement Manual Lift Knob Recommendation for Fan-Tastic Roof Vent

Question

Question:

We purchased two of these and installed them. The problem is, the plastic knob that opens the top vent did not fit well out of the box. We just worked with it, it is now completely stripped. Can I get a new one? The old vent had these in metal which was nice. Is there a replacement that will fit? I would like to have one for both units just in case. Let me know! Love the fans.

asked by: Brian

0

Expert Reply:

For a replacement operating knob and screw for your Fan-Tastic Vent Roof Vent, you will just need the part # FVK1142-09. This includes both the black plastic knob and the screw that you referenced.

expert reply by: Jameson C

0

Answer 1

Replacement manual lift knob #FVK1142-09 is going to be the best option we have for your 4251 series vent. This is the new style that replaces the old 4-wing knob.

view full answer...

Answer 2

The replacement manual lift knob for Fan-Tastic Vent Roof Vent is, #FVK1142-09. This works with Fan-Tastic powered vents, #FV803350 and #FV807350.

view full answer...

Answer 3

We carry #V2128SP-01 which does have a 110 volt fan. The vent #FV801250 has a 12 volt fan and unfortunately we do not carry a 110 fan as a replacement for it.

view full answer...

Answer 4

For a replacement operating knob and screw for your Fan-Tastic Vent Roof Vent, you will just need the part #FVK1142-09. This includes both the black plastic knob and the screw that you referenced. I spoke with my contact at Fan-Tastic Vent and they…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Manual Lift Knob Recommendation for Fan-Tastic Roof Vent

Products Referenced in This Question

Continue Researching