Dimensions of Trailer Side Mounting Plates on Stromberg Carlson Scissor Jack # JSC-24 and # JSC-30
Question:
The outriggers i have are junk. Will these fit this trailer. It looks like I need a 6-8 base to make it stable enough to work and tie in the parts of the frame. No welding.Can provide 1/4 plate if recommended. thanks installling on funfinder 21wbs What,s the width of the trailer side mounting area on the JSC-30?
asked by: Mark G
Expert Reply:
To determine if this jack will fit your Fun Finder trailer you will need to measure the location of where you will be installing the jacks on your trailer. I went out to our warehouse and measured the mounting plates on the Stromberg Carlson jacks.
The Stromberg Carlson Scissor Jack, part # JSC-24, has a trailer side base plate measurement of 10-1/4 inches in length and 3-1/4 inches in width. Each individual mounting plate would measure 3-1/4 inches wide x 3-3/4 inches length.
The bow-tie base plate would measure 8-7/8 inches in length and 7-7/8 inches hole-to-hole. The widest part of the bow-tie base plate is 4-1/2 inches wide and the smallest part measures 2-1/4 inches wide.
On the Stromberg Carlson Scissor Jack, part # JSC-30, the round trailer side mounting plate measures 9 inches in overall diameter. The diameter of the mounting holes on the plate measure 7-3/4 inches from center to center.
Product Page this Question was Asked From
Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
- Camper Jacks
- Fifth Wheel Camper
- Pop Up Camper
- RV Motorhome
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 9001 - 10000 lbs
- Scissor Jack
- 24 Inch Lift
- Bolt-On
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Continue Researching
- Shop: Lippert Scissor Stabilizer Jacks w/ Handle - 24" Lift - 10,000 lbs - Qty 2
- Search Results: lippert stabilizer
- Shop: Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - QTY 2
- Q&A: What Are The Mounting Bracket Dimension Of The Leveling Scissor Jack Set Part # JSC-24
- Shop: Ultra-Fab Ultra Scissor Jacks - 30" Lift - 13,000 lbs - Qty 2
- Shop: Lippert Scissor Stabilizer Jack - 24" Lift - 5,000 lbs - Qty 1
- Shop: Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4
- Shop: Replacement Key for Global Link RV Locks - 308 - Qty 1
- Shop: Replacement Key for Global Link RV Locks - 329 - Qty 1
- Search Results: stabilizer jacks
- Video: Review of Coghlans Patio Accessories - Outdoor Maintenance - CG78UV
- Video: Review of Valterra Patio Accessories - Outdoor Maintenance - VA64ZR
- Video: etrailer Scissor Stabilizer Jacks with Handle Review
- Q&A: Scissor Jack Replacement for Puma Travel Trailer
- Q&A: Are Mounting Holes of Trailer Mounted Stabilizing Jacks Universal
- Search Results: 2500 lb scissor jack
- Search Results: scissor jack
- Video: Furrion RV TV FUTVRS1-BL Review
- Video: Stromberg Carlson Leveling Scissor Jack Review
- Video: Stromberg Carlson Camper Jack - Leveling Jack - JSC-24 Review
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: Correct Replacement for Advent Analog Wall Thermostat ACTH1
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Can You Replace A GE Air Conditioner Be Replaced With An Advent A/C?
- Article: Best Ladder Racks
- Article: Trailer Maintenance Schedule
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Trailer Wiring Diagrams
- Article: RV Propane Troubleshooting | Common Propane Issues and How to Solve Them
- Article: Most Popular Wheel Bearings
on Trailer Jack
