Available Anti-Sway Stabilizer Bar for a 2015 Ford F-150

Question

Question:

Have a Ford F-150 2015 I need a stabilizer bar

asked by: Steve

0

Expert Reply:

For an anti-sway bar that is a confirmed fit for your 2015 Ford F-150 I recommend taking a look at the Roadmaster Rear Anti-Sway Bar # RM-1139-177. The bar attaches to your rear axle and chassis, enhancing stability by diminishing the roll that can be caused by winds or shifting cargo.

You may also want to consider the Timbren Rear Suspension Enhancement System # TFR1504E if your stability issues are happening when you are hauling cargo. These springs simply sit above your rear axle, minimizing body roll when turning while reducing sag and increasing overall stability.

I have added links to review videos of both products for you to take a look at as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 2

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 3

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 6

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 7

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 8

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that tears…

view full answer...

Answer 11

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 12

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...