Grease Seals for AL-KO T52 Axle with #42 Spindles and Bearings 25580 and 15123

Question

Question:

Looking for a oil/grease seal for a AL-KO Kober axle, Model T52 2, 4400 lbs. Do you have one?

asked by: Danny

1

Helpful Expert Reply:

Your AL-KO T-52 axle has # 42 spindles that use hub assemblies with a # 25580 inner bearing and # 15123 outer bearing. The grease seal most often associated with this bearing set is part # GS-2250DL for 1 seal or # RG06-070 for a pair.

expert reply by: Jameson C

1

Answer 1

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 2

Your AL-KO T-52 axle has #42 spindles that use hub assemblies with a #25580 inner bearing and #15123 outer bearing. The grease seal most often associated with this bearing set is part #GS-2250DL for 1 seal or #RG06-070 for a pair.

view full answer...

Answer 3

I have a couple of options for your 2021 Entegra Coach Accolade Motorhome to get you to the 16,000 lbs capacity you are looking for. There are no custom fit options available so depending on your frame you will either have to drill into it or weld…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Grease Seals for AL-KO T52 Axle with #42 Spindles and Bearings 25580 and 15123

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching