Load Extender Compatibility With 2017 Toyota Tacoma TRD Pro Hitch Receiver

Question

Question:

i have tacoma TRD Pro 2017 do you think this extender will fit on my tacoma hitch

asked by: Yusuf

0

Expert Reply:

The Malone Axis Truck Bed and Roof Load Extender for 2" Hitches # MPG907 will work with the hitch on your 2017 Toyota Tacoma TRD Pro. All hitches whether factory or aftermarket for your truck will have a 2 inch receiver and that is what is needed for this load extender.

expert reply by: Jason S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 3

For a made in the USA aluminum ball mount we only have adjustable units like the Flash Secure 2-Ball Mount #DTSTBM6600-2S which includes stainless steel hitch balls as well. The Fulton #F97CR you found as well as the similar Curt #C74WR and Brophy…

view full answer...

Answer 4

The Large Yakima OffGrid #Y07139 Cargo Basket uses crossbar clamps that are designed to be universal. They will fit virtually any crossbar shape, including most aftermarket and OEM crossbars. I was not able to find any schematics online that would…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

Yes, the TrackTowers part #Y52AV does fit into Yakima HD tracks like what you have installed on your trailer.

view full answer...

Answer 11

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Load Extender Compatibility With 2017 Toyota Tacoma TRD Pro Hitch Receiver

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching