Vehicle Fits for Westin E Series Nerf Bars 23-0530 and 23-1880

Question

Question:

I bought a set of second hand Weston E Series Nerf bars. They dont fit my truck as advertised. Im trying to find out what they do fit to resell them to recoup my losses. Heres what I know. Theyre chrome, 3inch bars. They have two pads on one side, one on the other and are 66 1/2inch overall length. What am I looking at?

asked by: Greg S

0

Expert Reply:

With a specific part number for the nerf bars I can look up the vehicle fits. The part # 23-0530 that you referenced is a set of 3-inch E-Series bars in stainless steel. These bars fit the following vehicles:

1980 - 1996 Ford Bronco Full Size
1980 - 1983 Ford F-100, F-150, F-250, F-350 Regular Cab
1992 - 1996 Ford F-150 Regular Cab
1984 - 1991 Ford F-150, F-250, F-350 Regular Cab
1992 - 1996 Ford F-250 and F-350 Regular Cab
1997 - 1997 Ford F-250 and F-350 Heavy Duty Regular Cab

The other 3-inch E-Series kit you referenced, part # 23-1880, fits the 2001 - 2003 Ford F-150 SuperCrew cab.

expert reply by: Adam R

0

Answer 1

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 2

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Vehicle Fits for Westin E Series Nerf Bars 23-0530 and 23-1880

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching