What is the Pilot Diameter of the CE Smith Trailer Hub Assembly # CE13100

Question

Question:

What pilot diameter rim does this fit?

asked by: Matt

0

Expert Reply:

On the CE Smith Trailer Hub Assembly # CE13100 the base of the side that your wheel will fit measured about 2-3/4 inches as demonstrated in the attached picture. Keep in mind that this hub has a 4 on 4 inch bolt pattern and the wheel with the maximum diameter that will fit it is 12 inches. This would work perfectly with a wheel like the Aluminum HWT Series S5 Trailer Wheel # AM22318HWT.

expert reply by: Jon G

0

click to enlarge

Answer 1

Hey Fred, The Trailer Idler Hub Assembly for 2,000-lb Axles #AKIHUB-440-2-1K being a 1/4" longer than your BT-100 hub would only be an issue if you had wheel hub covers that sit within that extra 1/4" of space. The grease cap is just going…

view full answer...

Answer 2

Yes, the CE Smith Trailer Hub Assemblies #CE13100 and #CE13110 will both fit on a BT8 Spindle #TRU94FR. The only difference between these 2 hubs is the Hub Assembly #CE13100 is threaded for wheel bolts and the Hub Assembly #CE13110 has wheel studs…

view full answer...

Answer 3

I went out to the warehouse and found that the CE Smith Trailer Hub Assembly #CE13100 measured about 4-1/4" but that was with the plastic still wrapped around it. If you took the plastic away it would probably measure closed to 4-1/8". The…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

Surge brakes use a hydraulic actuator to push fluid to the cylinder piston to activate the brake shoes on drum brakes or brake pads on disc brakes. This pressure should only be applied when weight is pushing against the hitch ball, so no pressure…

view full answer...

What is the Pilot Diameter of the CE Smith Trailer Hub Assembly # CE13100

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching