Will Any Drilling Be Needed When Installing the Air Lift Helper Springs on a 2012 Nissan Murano

Question

Question:

Does this need any drilling to be done to install this on my car? I have a 2012 Nissan Murano AWD

asked by: Naveen

0

Expert Reply:

I read through the installation instructions for the Air Lift 1000 air Helper Springs, # AL60774, and in section C of the instructions there is a step that stats that you may have to drill a 3/4 hole into the lower spring seat on certain vehicles.

The instructions does not say if this is true for the 2012 Nissan Murano. It just states that "some vehicles in this section do not have a hole in the lower spring."

There is a link toward the bottom of this page that will take you to the installation instructions for the Air Lift # AL60774 for you to review.

expert reply by: Jared P

0

Answer 1

According to the instruction for the Air Lift 1000 Air Helper Springs #AL60774 on your 2017 Nissan Murano, there is no step listed for removing the bump stop. This air bag works differently in that it is not providing vertical support like most…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 4

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 10

Hey George, thanks for reaching out! As long as you aren't towing more than the 3,400 lbs I recommend using the Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT82GR for your 2023 Volvo XC60 because of the completely removable hitch receiver…

view full answer...

Answer 11

Congrats on the new camper! I have a solution but there unfortunately is not a manual to electric conversion kit for the HappiJac 4160 series jacks. The reason an electric conversion will not work for your 4160 is that they have a two piece…

view full answer...

Will Any Drilling Be Needed When Installing the Air Lift Helper Springs on a 2012 Nissan Murano

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching