Will CE Smith Boat Trailer CE48810 Fit Sundolphin Paddle Boat

Question

Question:

I have a Sundolphin paddle boat that measures approximately 77 inch in length by 65inch in width. Will this trailer carry this paddle boat?

asked by: Phil S

0

Expert Reply:

The only size restrictions the CE Smith trailer has is that the boat has to be less than 12 feet in length and weigh less than 800 lbs. The bunks are on swivel brackets that you could adjust to fit the hull angle of your boat so it would work great for your.

expert reply by: Jameson C

0

Answer 1

The CE Smith Boat Trailer item #CE48810 is rated for a maximum speed of 65 mph. It is equipped with 4.80/4.00-8 bias ply tires that feature a speed rating of 65 mph. This is standard for most trailer tires. You won't have any problems at all with…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks #CE48870 that you referenced was designed to be used with boats that are up to 14 feet in length like what you have now. I attached a picture that shows the range of where the winch…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

We have the CE Smith boat trailer part #CE48810 which is designed for small boats like your 12.5 foot Flycraft inflatable boat. I attached a picture that shows a similar boat loaded on this trailer as well.

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Will CE Smith Boat Trailer CE48810 Fit Sundolphin Paddle Boat

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching