Replacement Vent Lid Recommendation for Older Jensen Style Vents

Question

Question:

Lost my skylight dome cover over the weekend. Need to replace but not finding on your site. I know ive purchased this cover from you in past. Id send a picture if you tell me how. Thanks -

asked by: Rick P

0

Expert Reply:

I was able to find you in our records and it looks like you bought the (three point hinge) part # 69284 back in 2015 which is discontinued. The new replacement part is # CAM40153.

expert reply by: Jameson C

0

Answer 1

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 2

Since the standard vent size is 14" x 14" (which is most likely what you have) you simply need to find out what hinge style your vent uses. There are 3 main types of hinges that we carry so I will give you some recommendations for our most…

view full answer...

Answer 3

We have a large selection of replacement lids for RV roof vents available. In order to pick out the correct replacement for your vent, you will first want to measure the vent itself. Most standard vents are 14 x 14 inches in size and fit into an…

view full answer...

Answer 4

Yes, due the the unique design of the MaxxFan Deluxe Roof Vent #MA00-07500K it can be left open while travelling. If you don't have the fan running while it's open the powered lift will close so if you plan on just having it open to vent…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Vent Lid Recommendation for Older Jensen Style Vents

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching