Comparison of Dexter and etrailer 7 Inch Brake Assemblies for Trailers with 2,000 Pound Axles

Question

Question:

What is the difference between # 23-47-48 and AKEBRK-2? As I look through their specs the only difference I see is the brand and price.

asked by: Nathan

0

Expert Reply:

The Dexter # 23-47-48 and etrailer # AKEBRK-2 brake assemblies are just that. The same part made by two different companies. They're both 7 inch brake assemblies for 2,000 pound axles. Both the left and right hand brakes are included and labeled to make it easier to install.

The etrailer brand does include the mounting bolts where the Dexter does not. For mounting bolts use # 7-75. Neither of them include the Mounting Hardware # BRKH7.

expert reply by: Charles S

0

Answer 1

To remove a hub from an axle, you will need to first remove the grease cap on the end of the hub. This will expose the end of the spindle. Once at this point, you will need to see if you have an EZ-Lube spindle, like #TRU77FR, or a standard spindle,…

view full answer...

Answer 2

When rotating tires like the #AM10303 on your triple axle trailer I recommend using the X pattern. This means you will swap the front driver side tire with the back passenger side tire, the front passenger side tire with the back driver side tire,…

view full answer...

Answer 3

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 4

As long as your existing hub drums are in good condition (no grooves worn in the armature surface that the brake magnet rides on or the surface that the pads grab). For a lot of trailer hub/drums there is a minimum thickness for that to be turned…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...