Replacement Security Allen Key for Rhino-Rack Roof Rack

Question

Question:

hi there, we bought a car with rhino roof racks, but never got the allen key..is there some other way we can remove the roof racks from our vehicle, but also to be able to use them again should we need to?

asked by: Anke

0

Expert Reply:

I have the perfect solution for you! You can actually order a replacement Security Allen Key from our site; part # SECKEY-L for Long or part # SECKEY-S for Short. Either of these will allow you to remove and re-install your Rhino-Rack roof rack.

expert reply by: Jon G

0

Answer 1

Yes! You can get the replacement Rhino Rack Security Key which comes in two sizes: Short #SECKEY-S or Long #SECKEY-L. Both will work on the bolts on your Rhino-Rack Nautic Roof Kayak Carrier #RR570, it just depends how much length and leverage you…

view full answer...

Answer 2

You would need to use the Allen key to remove the Rhino-Rack roof rack #RR78MR every time. But it isn't as difficult or time-consuming as it sounds. After you have done the initial installation and have taken the rack off and put it back on a…

view full answer...

Answer 3

The first thing you would have to do is remove the bars. This can be done by using a 5mm Allen wrench and unscrewing the bolt underneath each foot. Then you would remove the legs from the base. I would use some lube on the locking levers just in case…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The Progressive Dynamics Replacement Section #PD4655V does have a jumper to change the charging profile to lithium compatible. You'll simply need to move the black jumper over from the WIZ side to the LI side.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Replacement Security Allen Key for Rhino-Rack Roof Rack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching