Replacement 8,000 lb 5th Wheel Landing Gear Set for 5th Wheel Toy Hauler
Question:
Need a new jack for my 5th toy hauler camper it is a 36 foot unit the one I is stuck and well not operate. Trailer jack are 2.5x2.5 square the main. Tube 33.5 inches long and we think it's 8000 pounds
asked by: Bruce
Expert Reply:
The Landing Gear Set part # RVLG-8000 is rated for 8,000 lbs like what you believe your current landing gear's weight capacity is. It also has a leg height of 32-3/4 inches to 53-1/4 inches giving you a travel of 20-1/4 inches which will work well for your application. This jack can be operated manually using part # RVLG-HDL or with a 12V DC motor using part # LC142178.
The weld stops on this landing gear set have distance of 15-1/2 between the bottom of the upper weld stop and the top of the lower weld stop. The measurement from the top of the upper weld stop to the bottom of the lower weld stop is 17-1/2 inches (see attached picture). Even though these are standard measurements you will want to go out and measure your current weld stops to see if this is compatible. If they are not the same measurements then you can either remove one of your current weld stops and have a professional welder install a new one in the appropriate place or you can have the weld stops removed and this set welded on.
Some landing gear legs are compatible with each other but since it is not a guarantee it is always wise to go ahead and replace both legs at the same time so that they extend and retract at the same rate.
I have attached a demonstration video where one of our team members goes over a few more features of the landing gear that you can check out.
Products Referenced in This Question
Lippert Venture 5th Wheel RV Landing Gear Motor
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Lippert
more information >
Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- etrailer
more information >
Product Page this Question was Asked From
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Q&A: 5th Wheel Landing Gear Motor Makes Loud Clicking Noise and Will Not Raise Trailer
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Q&A: Replacement Crank Handle for Ram 5th Wheel Landing Gear Compatibility With 2007 Fleetwood Nitrous TT
- Article: Best Landing Gear
- Q&A: How Much Weight Can Landing Gear Hold
- Q&A: Troubleshooting Clicking Noise Coming From Landing Gear or Motor
- Q&A: How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
- Article: How to Choose a Bike Rack for a Motor Home or RV
- Article: Trailer Wiring Diagrams
- Article: How Much Solar Power Do I Need For My RV?
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Does Solar Panel Type Really Matter?
- Article: Most Popular Wheel Bearings