Converting 4-Flat to 7-Way on 2005 Toyota Sienna to Use Prodigy RF Trailer Mounted Brake Controller
Question:
Is this the correct product to use when I just want to convert the flat 4 trailer connector I have on my 2005 Toyota Sienna to a round 7 for use with the Prodigy RF? All of the instructions are related to using an installed brake connector.
asked by: Noel P
Expert Reply:
If you elect to go with the Tekonsha Prodigy RF Brake Controller, item # TK27FR, on your trailer, instead of installing a brake controller in the cab of your 2005 Toyota Sienna, you will not need all of the items and wiring in the Electronic Brake Controller Wiring Kit, # ETBC7.
For the Prodigy RF to function properly all that is needed is the constant 12 volt power supply from the vehicle battery. You would need the following items:
# 37185 7-Way and 4-Way adapter, plugs into your existing 4-Flat connector
# 10-1-1, 10 Gauge Wire, Sold by the Foot
# PK54540, 40 Amp Circuit Breaker, 1 Each
# DW05705-1, Ring Terminal, 3 Each
Connect an appropriate length of the 10 gauge wire, # 10-1-1, to the black wire on the # 37185 connector and run it forward to the engine compartment. Then, connect the end of the 10 gauge wire to the AUX side of the 40 amp, # PK54540, circuit breaker. Finally, connect the BATT side of the circuit breaker to the positive battery terminal on the vehicle battery. Make sure to connect the white ground wire from the 37185 connector to the vehicle frame and the installation is complete. Since you will not need the Blue and purple wire from the adapter you can tape or cable tie them up out of the way for future use.
Instructions to complete installation of the Prodigy RF on your trailer are linked for you to review.
Products Referenced in This Question
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Ring Terminal - 12-10 Gauge Wire - 3/8" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/8 Inch Diameter
- 12-10 Gauge
- Deka
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Replacement Handheld Remote for Tekonsha Prodigy RF Brake Controller - Bluetooth
- Accessories and Parts
- Trailer Brake Controller
- Remote Control
- Tekonsha
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Where Do the Wires on the Universal Install Kit for Trailer Brake Controllers Get Installed?
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: Should I Get a Proportional or Time-Delayed Brake Controller
- Q&A: Parts Needed to Tow Trailer With Brakes Using 1992 Dodge D250
- Q&A: 4-Flat Trailer Wiring For 2024 Jeep Wrangler With Tow Bar Wiring