Why Does Bumper Beam Get Removed to Install Draw-Tite Trailer Hitch on a 2017 Jaguar F-Pace
Question:
Jaguar F-Pace S. impact bumper bumper beam removed and not reused using draw-tite., When use Curt it appears this item is reused. Is that correct and if so why the difference?
asked by: Thomas G
Expert Reply:
On your 2017 Jaguar F-Pace the bumper beam is removed for installation of the Draw-Tite hitch # 76026 because the cross tube spans the space between where it mounts to the vehicle. The bumper beam is curved but doesn't stick out far enough on the ends for the design of the hitch. The bumper beam is therefore removed and the hitch basically takes its place.
On the Curt hitch # C13291 the cross tube is not as long so the curved bumper beam can fit around it and you won't have to leave it off of the vehicle.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
And for a trailer wiring harness you can use # 118785 to add a 4-Way flat connector to the rear of the vehicle.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 900 lbs TW
- 6000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Will Curt Hitch Work With 2017 Jaguar F-Pace With Dual Exhaust on One Side?
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Replacement Hub/Drum for Triton Axle 08353
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Should Leaf Spring Capacity Match Trailer Weight or Axle Weight for Best Ride Comfort
- Q&A: Replacement Bearing Kit and Bearing Buddy Grease Caps for 2012 Triton LT Trailer with Reliable Axle
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: Is Leaf Spring Capacity Rating for One Side or Two
- Q&A: How Close to Trailer Weight Should Capacity of Trailer Leaf Spring Be
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Roof Rack Information
- Article: RV and Camper Types, RV Classes
- Article: How to Tie Down Skis and Snowboards to a Roof Rack
- Article: Trailer Wiring Diagrams