Will The GM Adapter # D13035 Fit A 2007 Chrysler 300C?

Question

Question:

Regarding D13035. Do you think this GM adapter would fit my 2007 Chrysler 300C with 5.7 L engine? My transmission cooler line fitting has a 1/2inch quick connect and my transmission lines are 3/8. I noticed the shape of the end of this D13035 corresponds with the shape of the end of my OEM transmission cooling line. What are the dimensions of this D13035? Thanks and Im sorry to have emailed you twice about this challenge Im trying to solve.

asked by: Brian G

0

Expert Reply:

For your 2007 Chrysler 300C, the Derale Snap-In Radiator Adapter Fitting for GM # D13035 may fit but I can't confirm it. Most of the transmission coolers come with an insta-dapt radiator adapter like # D13004 that fits most vehicles and has both male and female threads to fit 5/16 inch transmissions lines. The GM specific adapter is a much nicer option for vehicles that fit, but your Chrysler is not on the list of confirmed fits.

expert reply by: Jason S

0

Answer 1

I believe what could possibly work for you is the Derale Snap-In Radiator Adapter Fitting for GM #D13035 which measures 2" overall, .48" on the larger flare side, .43" on the smaller end, is .37" in diameter, and…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Will The GM Adapter # D13035 Fit A 2007 Chrysler 300C?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching