How Does Extang Trifecta Tonneau Cover Install on 2015 Nissan Frontier with Utili-Trac System

Question

Question:

I have the utili trac system in my truck. Does this fit? If so what type of adaptor is available to clamp on. The standard clamps do not grip the bed rail directly with the tracks in place.

asked by: Rod D

1

Helpful Expert Reply:

The Extang Trifecta Tonneau cover # EX92985 comes with a special adapter that allows the cover to install on your 2015 Nissan Frontier 5 foot bed with the Utili-Trac system. I included an image from the instructions showing how it works.

expert reply by: Michael H

1

click to enlarge

Answer 1

Yes, the adapter clamps that are used to secure the Extang Trifecta 2.0 Tonneau Cover #EX92985 to the Utili Track on your 2018 Nissan Frontier can be found with part #EX2244-0204. This includes all 4 clamps needed for installation. If you can tell…

view full answer...

Answer 2

I spoke to Extang and their Trifecta 2.0 Soft Tonneau Cover #EX92985 will not fit with utility track system that you have on your 2020 Nissan Frontier. We do have the Access Vanish Soft, Roll-Up Tonneau Cover #834532007943 which is confirmed to fit…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Thanks for reaching out, Scott! The Blue Ox Base Plate Kit #BLU74FR on our site is actually the same thing as the Blue Ox part number BX2418 and I like that removable pin style much more than the etrailer Classic Base Plate Kit #e98945 with the fixed…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

I do say those welds are bad and it appears the bumper is simply welded onto the back plate of the trailer rather than the frame. I recommend removing the entire bumper for the Mount-n-Lock Heavy-Haul'r Replacement RV Bumper #MNT43VR which you…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Since your weight distribution hitch is working to keep your 2020 Ram 1500 level I recommend going for the lighter Blue #SSR-307-40 springs. These have the 1" spacer as well like the heavier Black #SSR-307-47 springs which you can take out or…

view full answer...

Answer 12

Hey there Stormy, I think we can figure this out, as there are a quite a few options. First, let's just discount the heavy-duty rack, as those are just oddly shaped crossbars and there's nothing HD about them (like you mentioned, they have…

view full answer...