Why Do LED Taillights on Vehicle Cause "Bulb Burned Out Message on Dash
Question:
I have a 2003 Dodge Ram 1500 and I ordered new tail light Spyder Brand- 3 light set and a new brake light bar and I installed the left one first and it worked fine. Installed the right side and my dash light came on saying tail light out. Why would the left work and not the right? I checked the website out and it said to add a resister. Do I really have to do that?
asked by: Tom C
Expert Reply:
When you replace incandescent bulbs on a vehicle's turn signal circuit with LEDs the blinker circuit doesn't want to work right. This is due to the amperage rating being too low on the LEDs and thermal flasher units needing to see a specific amperage rating to work right. Now with some vehicles if the circuit doesn't see a specific amperage load on the circuit it thinks the bulb has burned out. The LEDs will cause this. A load resistor puts that same amperage back on the circuit so that it thinks the lights are all working properly.
For a load resistor we have the part # PDI34ZR. You most likely just got lucky with the first circuit you installed the LED on.
Products Referenced in This Question
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Product Page this Question was Asked From
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Shop: Fifth Wheel Hitch
- Shop: Front Mount Hitch
- Shop: Vehicle Engine Heaters
- Shop: Backup Camera for Edge Color Touch Screen (CTS) Monitors
- Shop: Shocker 5th Wheel to Gooseneck Pinbox for Lippert 1716/1116/0115 and Fabex - 24K GTW - 6K TW
- Shop: Kat's Heaters Thermal Battery Wrap for Series 24, 24F, 27, 27F, 74 Batteries - 125V - 80 Watt
- Q&A: Troubleshooting LED Trailer Lights Causing Error Code On 2021 GMC Sierra Denali 2500
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Pigtail - Qty 1
- Video: Optronics Lights ALEDRST1B Review
- Video: Review of Command Electronics Trailer Lights - Triple LED Stop Turn Tail Reverse - CE44VR
- Shop: Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens - Qty 1
- Video: Review of Diamond Lights - Load Resistors - DI34ZR
- Shop: Truck Bed Sliding Tray
- Shop: Performance Chip Tuners
- Q&A: Load Resistor Recommendation for Use with LED Tail Lights on a Flat Bed Truck with Hyperflash
- Q&A: How to Find Replacement Tail Lights for Your Trailer
- Q&A: Replacement Taillight for 2016 Winnebago Winnie Mini Class C
- Q&A: Replacement Tail Lights for 2016 Forest River FR3 Class A
- Q&A: Will Command Electronics Triple LED Trailer Tail Light Fit 2010 Coachmen Freelander
- Search Results: goosebox
- Search Results: gen~y hitch
- Shop: Gooseneck Hitch
- Q&A: How To Install Load Resistor Kit For LED Turn Signals That Flash Quickly
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 68149