How to Make Template to Determine Where MaxxAir Roof Vent MA00-06200K Would Install on Roof

Question

Question:

I am doing a van conversion on a 2000 Dodge Caravan. The roof ribs are pretty tight. Is it possible to get a template for the 14inch x 14inch inch opening I need to cut to see if this fan will fit? Is there somewhere to download one, or can I buy just a template or gasket to actually put on the roof to see where this will fit - if it will fit - before I order it? Thank you! I worked for Camping World as a customer service rep and these fans were by far the favorite of those customers who had tried both the Fantastic and the MaxxAir. So, when it comes time to buy I know what I want!

asked by: Becky B

1

Helpful Expert Reply:

We don't have a template we can offer but if you measure a 14 inch by 14 inch square you'll know where the # MA00-06200K would install. You could pretty easily draw out a 14 inch by 14 inch square on some cardboard and you'd basically have a template.

expert reply by: Jameson C

1

Answer 1

The best option we have is the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote #MA00-07500K which is the smoke color you want, has the highest CFM rating of 900, and comes with a remote. It is power lift though which is going to be the…

view full answer...

Answer 2

The MaxxAir MaxxFan Trailer Roof Vent #MA00-06200K extend 9-5/16" above the roof when it is opened and 5" when it is closed. This is actually on par (or slightly under) with most other roof vent styles. Since this is a manual lift you can…

view full answer...

Answer 3

Well the assembly and lid of the MaxxAir MaxxFan Trailer Roof Vent #MA00-06200K are made from plastic so it's not going be be highly impact-resistant. Small tree branches wouldn't be a problem but large hail would damage the lid for sure. For…

view full answer...

Answer 4

The fan of the MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan - w/ Rain Cover #MA00-06200K draws 5 amps. In theory a 750 amp battery would power this for 150 hours.

view full answer...

Answer 5

In order to properly measure your RV's vents, you will want to measure the size of the rough opening in your RV's roof. This can be measured by removing the garnish around the vent on the inside of the RV and measuring the size of the rough…

view full answer...

Answer 6

Although we do not have a direct replacement for the Dicor V19582-EJN, the Replacement Wheel Master Lug Nut Cover for Wheel Liner - Qty 1 #WMRMT9061 will fit a 22 millimeter lug nut. From what I have found, the jam nut you are looking for has been…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The Dometic Ultra Breeze Trailer Roof Vent Cover part #DMC38FR installs using brackets which secure to the vent lid flange. The brackets are screwed into the roof but the cover is attached to the bracket using pins and is easily removeable. I have…

view full answer...

Answer 9

I recommend the Alpha Systems Butyl Tape for RV Weatherproofing #AL28FJ as it's 1" wide to fully cover the flange of your vent. Make sure you overlap the ends to form a tight waterproof seal. You can see me doing this at 2:50 mark in the…

view full answer...

Answer 10

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

How to Make Template to Determine Where MaxxAir Roof Vent MA00-06200K Would Install on Roof

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching