Parts Needed to Add Electric Brakes to 6 x 14 Cargo Trailer with a 3,500 Pound Axle
Question:
Hello, I want to install brakes on my 6x14 single axle continental cargo trailer. Do you know the kit I would need for that? It has the 3500 lb dexter axle. I would need to convert it to a 7 pin connector, and the correct wire for hooking it up as well. Bearings are L68149 inner L44649 outer 5 on 4-1/2 pattern Thanks
asked by: Ryan
Expert Reply:
The brakes I suggest for your 3,500 pound axle are the self-adjusting # AKEBRK-35-SA assemblies. Since they're self-adjusting you need to do an adjustment when you install them but that's it.
The hub and drum assembly to match your bearings and bolt pattern is # AKHD-545-35-EZ-K. This includes new bearings, races, grease seal, grease cap, and lug nuts.
For the 7-way trailer connector I like # HS381-9000. It attaches to a junction box to make wiring everything easier. You'll also need ring terminals, # 44-5310A, to connect the wiring. Then use about 20 feet of 10 gauge wire # 10-1-1, which is sold by the foot, to run the wire from the junction box to the trailer's brakes.
The trailer will require a breakaway kit. The Hopkins Engager # 20099 is our most popular kit. The breakaway kit engages the trailer's brakes in the event the trailer is separated from your tow vehicle.
In order to control the trailer's brakes you must have an electric brake controller in your tow vehicle. I suggest the Prodigy P3 # 90195 because of how reliable and easy to use it is. Its one of our top brake controllers. If you tell me the year, make, and model of your tow vehicle I'll see if we have a custom harness to install the controller. And also anything else that may be necessary.
I've linked some videos on the products I've recommended for you to take a look at.
Products Referenced in This Question
Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- Hopkins
more information >
Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/16 Inch Diameter
- 12-10 Gauge
- Flint Hill Goods
more information >
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Wiring
- Hydrastar
more information >
Product Page this Question was Asked From
etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Self Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Testing Trailer Brake Magnets for Proper Function
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Hub and Brake Assembly for AL-KO 8490
- Article: How to Tell the Weight Rating of a Trailer Axle
- Q&A: Can Electric Brakes be Used on a Boat Trailer
- Q&A: Correct Replacement for AL-KO 7230 Hub/Drum and Brakes
- Q&A: Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle
- Q&A: Replacement Trailer Brake Assemblies with Axletek-10-GG On Assemblies
- Q&A: Are New Brake Drums Required if Replacing Electric Brake Assemblies on a Trailer