Replacement Nut and Bolt for Yakima RailGrab Towers

Question

Question:

I lost a nut from one of my claws. Can you verify the thread for the bolt/nut assembly? Purchased all these from you guys back in 2014 or so. Thanks

asked by: Russell B

0

Expert Reply:

The Yakima RailGrabs, which replaced the LowRider line of towers, and is now itself discontinued, did not have any changes to the hardware over its life span so # Y8880279 will fit your RailGrab towers. If you need the wedge assembly it is # Y8880150. If you need any other RailGrab parts let me know and I can see if they are available.

expert reply by: Michael H

0

Answer 1

You made a great choice in the Lippert Components Power Stabilizer Trailer Jack. For starters, all of the jacks measure to be 70-1/2" long with a 3,500 lb weight capacity and have a 30" lift. The difference between them is in…

view full answer...

Answer 2

We do have a hitch extender that may work for your 2014 Dodge truck. If the hitch has a 2 inch receiver opening, I recommend the Blue Ox Hitch Extender for Tow Bars, part #BX88264. When installed this extender moves the extender opening 12 inches…

view full answer...

Answer 3

It sounds like your RV has the outriggers or something similar. For new outriggers we have #LC301704 you can use.

view full answer...

Answer 4

The online owner's manual for the 2016 Ford Explorer Sport indicates (on page 324) that tire chains may be used on size 245/60-18 front tires only and so long as they are S-Class chains that do not require more than 10mm of clearance. You'll…

view full answer...

Answer 5

We offer specialized roof racks made just for pop-up camper trailers like your Jayco 12HW and we also offer RV bike racks in several varieties. As a starting point I suggest you confirm the weight rating for the camper top. An average adult bike can…

view full answer...

Answer 6

The pinout of the #30104 that you referenced will only work on Jayco trailers. Although the connector is the same the wires are run to different pins on the 6-way side of the connector. Your best option would be to cut off the 6-way on your trailer…

view full answer...

Answer 7

The Black Rubber Grommet for 4 inch Round Trailer Lights, part #A45GB, mounts in a 4 1/2 inch diameter hole. This grommet will work with the Sealed 4 inch Round LED Trailer Light, part #STL23RB, and should work with your fiberglass application. The…

view full answer...

Answer 8

We may have the bearings you need, but the spindle dimensions you have aren't standard hub dimensions so you may have something that there aren't replacement parts for. For a bearing that has an inner diameter of 1.25 inches and an outer…

view full answer...

Answer 9

Yes, you can get replacement hardware kit #RHK which will replace all the hardware for the hitch. Just enter the hitch number where indicated on the page and our team of hardware ninjas will compile the proper kit.

view full answer...

Answer 10

It sounds like you have a gooseneck like the Atwood Gooseneck Trailer Coupler AT75401. For an adapter to kingpin, I recommend the Bulldog Gooseneck-to-5th-Wheel Trailer Coupler Adapter - Inner Tube - Square - 30,000 lbs #BD0289650300 or the…

view full answer...

Answer 11

To install the Kat's Heaters Custom Fit Engine Block Heater #KH11814 you will need to locate the cartridge hole on the block, which for a Chrysler it will be on the left or right rear of the block. You will need to clean the hole out and then…

view full answer...

Answer 12

First thing to try is soaking the hitch ball in as much WD-40 that you can so that you can hopefully free it up. Let it sit overnight and maybe hit it with a rubber mallet as well. The next thing you can try is putting the weight of a gooseneck…

view full answer...

Replacement Nut and Bolt for Yakima RailGrab Towers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching