Replacement Screen Door Handle Latch For RV

Question

Question:

we have screen door handle latch broken, the part # is 282385, it is mark on it Excel

asked by: Germain L

0

Expert Reply:

To replace your screen door handle latch, I recommend the Lippert Components RV Entry Screen Door Latch - LH # LC201472 or the right hand side # LC201471.

These can be used with the Lippert Components RV Screen Door Frame Striker # LC198287 and the Lippert Components RV Outside Striker for Screen Door # LC198252.

expert reply by: Jason S

0

Answer 1

The Lippert Components RV Entry Screen Door Latch - RH #LC201471 is the latch used in the attached installation video. If you need the opposite side for doors that swing out with hinge on the left, then you would use the Lippert Components RV Entry…

view full answer...

Answer 2

When determining what screen door latch you would need either the right hand or left hand side you would need to look at the closed door from the inside of your RV. The latch location is the side of the door that it is mounted on. This would mean…

view full answer...

Answer 3

What you want is the Right Hand Side #LC201471 as opposed to the Left Hand Side #LC201472. If you check out the attached installation video you can see that this door is configured the exact same way that you mentioned.The latch itself on both…

view full answer...

Answer 4

The mounting holes on the Lippert Components RV Entry Screen Door Latch #LC201471 (RH) and #LC201472 (LH) are 3" apart. The latch has a total length of 3-5/8" and is 1-1/8" wide.

view full answer...

Answer 5

I went and pulled a Lippert Door Latch part #LC201471 from our warehouse to get the dimension you requested and found it to be 3 inches from one mounting hole to the other.

view full answer...

Answer 6

I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-468-469 to replace your brakes on your 2009 Forest River Surveyor SV291 with your 3,500lb axle. These brakes will automatically adjust as they wear to ensure longer life and better…

view full answer...

Answer 7

You're not going to have any problems mixing Dexter and Lippert components on trailer axles over 10k-lbs in the same manner as below 10k-lbs as long as the measurements on the replacement parts are the same- i.e. bearing sizes are the same, etc..…

view full answer...

Answer 8

The Global Link RV Entry Door Part #295-000019 that you referenced is designed to fit the standard styles of doors that are found on nearly all RVs. The hole cut out needs to measure 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall…

view full answer...

Answer 9

It is likely that the interior gears have stripped when the jack over-extended. If you have the manual crank that should have came with the jack, use it by removing the rubber plug at the top of the jack, insert the crank and fit it to the override…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Replacement Screen Door Handle Latch For RV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching