Recommended Trailer Hitch Receiver, Ball Mount, And Wiring For 2003 Saab 9-3 Sedan
Question:
Im looking for a hitch for my 2003 Saab 9-3 sedan. And would like to know what the difference is between curt #11326 and 113262?? Also is the wiring kit safe to put on this car without any error lights on the info display in the car?? Thanks.
asked by: Andres P
Expert Reply:
For your 2003 Saab 9-3, the difference between the hitches is connection points to the frame. There is a compatibility issue for the Draw-Tite hitch on a sedan, so the only confirmed fit for your vehicle is the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11326. I think you got confused because it was listed twice because it is a fit for a convertible as well as a sedan. I've linked a couple videos of this installation for you.
If you will be doing some light towing with this hitch, I recommend the Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs # C45521 confirmed to fit this hitch. You will also need a hitch ball like # A-80 and the pin and clip # F-4.
For your vehicle wiring, I recommend theCurt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236. This harness is confirmed to fit your vehicle and won't cause any errors or warnings to display in your vehicle. It will draw power directly from the battery to power the converter and will only draw the signal from your factory wiring.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Preventing Exhaust Heat From Hitting The Kuat Sherpa 2.0
- Article: Trailer Hitch Receiver Sizes
- Q&A: 2006 Saab 9-3 Aero with Dual Exhaust Trailer Hitch Compatibility
- Article: My Trailer Hitch Doesn't Fit
- Q&A: How to Determine if 2017 Jeep Compass is New or Old Body Style for Picking Out Hitch
- Q&A: Recommended Methods to Test Brake Controller Output on Chevrolet Truck
- Q&A: Where is the Brake Controller Plug on my 2019 Chevrolet Silverado 1500 LD
- Q&A: Trailer Hub that Uses Bearing # LM67048 for Inner and Outer
- Q&A: Replacement Bearings for Dexter 3000 lb Trailer Axle
- Article: Rooftop Cargo Carriers
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Trailer Wiring Diagrams