What are the Dimensions of 1000 Pound Equal-I-Zer Spring Bar # EQ90-02-1099

Question

Question:

What are the dimensions of this Spring Bar?

asked by: David M

0

Expert Reply:

Replacement spring bar for 1000 pound Equal-I-Zer systems # EQ90-02-1099 is 36 inches long and 1-3/8 inches wide. The different Equal-I-Zer systems have different heads for the different spring bars so as long as you currently have the 1000 pound system this bar will work.

expert reply by: Michael H

0

Answer 1

I spoke my contact at Equal-i-zer and he told me that since it has 1 1/2" bars it is probably rated for 12,000 lbs. He said the way to tell for sure is to measure the bolt channel. If it measures 3/8" it is a 12,000 lb hitch, if it measures…

view full answer...

Answer 2

It could be some sort of issue with the steel on your Equal-I-zer weight distribution system #EQ37140ET. Frequent overloading of the hitch could also cause this issue. I'm not saying that you overload the system but that is just one possibility.…

view full answer...

Answer 3

Yes you can just swap out the bars on your Equal-i-zer Weight Distribution System w/ 4-Point Sway Control #EQ64FR with the Replacement Spring Bar for Equal-i-zer Weight Distribution Systems #EQ90-02-1499.

view full answer...

Answer 4

The best hitch for a 2024 Hyundai Tucson is the etrailer Hitch item #e38KR. This hitch is custom fit and bolts to your Tucson with included hardware. It is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 525 lbs…

view full answer...

Answer 5

Yes, the hole referenced is going to be the part that the spring bars fit into. For instance, if you measured 1 3/8" like how its shown in the attached image, then you'd need the Replacement Spring Bar for Equal-i-zer Weight Distribution…

view full answer...

Answer 6

You would not be able to simply replace the spring bars on your Equal-i-zer #EQ37060ET weight distribution hitch. Instead you would need to get both the 1,000 lb tongue weight spring bars #EQ90-01-1099 as well as the 1,000 lb head unit…

view full answer...

Answer 7

Unlike some weight distribution systems, the weight distribution head of the Equal-i-zer hitches also carries a bar-specific weight capacity so you unfortunately wouldn't be able to increase the weight capacity by just going with a higher rated…

view full answer...

Answer 8

If you order a quantity of 6 of the Camco Cam Lock #CAM44340 they'd all show up keyed alike.

view full answer...

Answer 9

Your weight distribution system, #EQ37120ET, is rated for a total tongue weight of 800-1200 lbs. That total tongue weight is the loaded tongue weight of your trailer as well as any cargo behind the rear axle of your tow vehicle. I've attached an…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What are the Dimensions of 1000 Pound Equal-I-Zer Spring Bar # EQ90-02-1099

Product Page this Question was Asked From

Continue Researching