Replacement Trailer Jack Recommendation for Shelby Jack 5854A

Question

Question:

Hello I am inquiring about purchasing a new tongue for my Shelby trailer, model 5854A. It was bent during a minor accident.

asked by: Paige P

0

Expert Reply:

The specific Shelby jack you are looking for is not available from us but for a very similar jack we have the Fulton part # FXPD15L which uses a similar mounting style, is a sidewind, and has a wheel caster setup.

expert reply by: Jameson C

0

Answer 1

I do have a solution for you, however replacement parts for your Shelby 5854A Trailer Jack are no longer available. I recommend simply replacing your Shelby jack with a similar unit like the Fulton Bolt-Thru Swivel Trailer Jack #FXPD15L. This zinc…

view full answer...

Answer 2

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 3

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Answer 8

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Trevor, so the B and W Companion Slider hitch part #BWRVK3400 only fits the B and W Turnoverball gooseneck hitches and would not fit the gooseneck hitch of your 2022 Chevy Silverado 2500 with OEM pucks. The funny thing about the Patriot slider is…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 12

Thanks for the pictures! To replace your Curt Turning Point you will want the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR. This was made specifically to replace the Turning Point pin boxes. You will also need the Safety…

view full answer...

Replacement Trailer Jack Recommendation for Shelby Jack 5854A

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching